Thinking about buying or insuring a boat in Preveza Greece??

Friday 29 May 2015

Easticks 28 for Survey at Coxes Boatyard

Today's assignment was to carry out a Prepurchase Survey on this Easticks 28 Yacht. Production Years were from 1980-96 and the builder was Easticks Yacht Station in Acle, Norfolk. The original Easticks fleet were sold off to the Caister Group in 1965. The Caister Group had undertaken a mass buy out of many fleets in 1965 and, whilst most of those remained where they were and ran under the old yard's name, the distinction was made with the Eastick's fleet which were moved to Potter Heigham and ran under the Herbert Woods name..... thus the yard and Easticks name were retained by the owner.


The new sheds at Coxes boat yard have tons of room for all types of craft.

Easticks are know to have a slightly offset keel moulding giving the impression of a bent keel! 


Wow, how White boat prices have dropped since fiberglass versions became more popular, a good wooden one can now be bought for £5,000. 


Wednesday 27 May 2015

Project 31 motor cruiser for Survey at Richardson's Boatyard

Hi had a trip over to Moonfleet Marine today to take a look at this Old Classic Cruiser! 
This craft was launched in 1966 and continued up to 1974. The boat is a large cockpit cruiser with an evolved hull design from a stretched Elysian 27. The cabin is open plan, but with a folding partition and curtains giving optional privacy to the V berths forward. The interior has 2 V berths to bow with a table dinette further aft. 

All craft were outdriven and a huge variation of engines fitted from single petrol to larger diesels. This example had the two 4108 diesel taxi engines with enfield drives. 


On a vessel of this age that has spent most of her life in freshwater, you are going to get some type of osmosis on the underbody. Experience has shown that early treatment of osmotic boats tends to be less successful than treatment of vessels with more advanced problems. While this may seem to contradict normal precautionary practice, it has been found that breakdown reactions in GRP laminates take some time to reach their conclusion; and if treatment is carried out prematurely it is much more difficult to remove reactive or hygroscopic compounds from the laminate, with the result that a recurrence of osmosis is much more likely to occur. The overriding factor must always be the integrity and safety of the hull. Osmosis in its early stages is very much a chemical condition, which has very little effect on hull strength. 

Perkins 4108 diesel: If it has been well maintained it should go well past 10,000 hrs, maybe double that. You will have to keep up proper maintance. Make sure your impeller, heat exchanger, anti siphon valve and exhaust mixing elbow are kept in good shape. Also make sure that your fuel tanks are clean and your fuel filters are changed regularly.Most diesels will run trouble free for thousands of hours given clean fuel, oil, and air.  

The boat is a round bilge hull design of semi displacement style.The boat has a large cockpit and open-backed wheelhouse. A settee in the cockpit can be pulled out to form an additional fair-weather berth. 





Wednesday 20 May 2015

Storebro Baltic 31 for Survey at Norfolk Yacht Agency

A surveyed this true classic Scananavian cruiser today at Norfolk Yacht Agency in Brundall.

She has a stoutly built semi displacement hull.

All versions I have seen have the Volvo AD40 diesel engines in twin form on conventional shaft drives. 





Surveyors comments: The craft are a proven coastal boat and in soft top form (as opposed to hard type design) capable for river use.

Monday 18 May 2015

History - Broads Cruiser?


Can anyone help me find out the history of this little cruiser, shes seems to have been built for sea going, around the 50's. The owners desperate to find out more...anyone? steventruss1@aol.com 

Broom 44 Survey at Norfolk Boat Sales

I had the day at Norfolk Boat Sales in Brundall Surveying this Broom 44 TSMY.
The 44 was produced as a Hardtop with fixed doors aft of the helmsmans seat, and also as this example the Mediterranean, which had a standard removable canopy and an open aft cockpit. 


These boats were fitted with a variety of twin engine configurations between 185HP and 220HP including these the Ford Sabre 420's as well as Caterpillar or Volvos.




The bathing platform is integral to the hull but the access to the deck is still by stainless steel ladder at this time. The 44 is distinguished by its rectangular portholes forward and aft.
The large deck saloon was laid out with lounge seating aft on the port side, and a dinette on the same level but forward on the starboard side. Steps lead down to the port side galley and forward heads. The standard layout was for an island double in the forward guest cabin although in some boats this was replaced by V-berths. The large third cabin was fitted with overlapping twin bunks.
Surveyors comments: In its day the flagship of the Fast Offshore range, the 44 combines a vee hull for fast offshore passages with a skeg keel providing good handling qualities.

Thursday 14 May 2015

Aquafibre 42 for survey at Anglia Yacht Brokers

I had the day at Anglia Yacht Brokers in St Olaves yesterday Surveying this Aquafibre 42 River Cruiser.
The first Aquafibre hull was the Ocean 30, one of the most used moulds in motorboating history. It initially became the Broom 30 and Moonraker 30, before being used to create scores of other models up until the present day.


The second mould from Aquafibre became the much-loved Ocean 37 and Broom 37.

Aquafibre was started in 1965 at the outset of moulding in GRP and its success in doing so was hugely influential. The firm went on to play a key role in development for Fairline and worked with some of the big names in modern motorboating, Broom and Princess among them.
The firm grew rapidly, supplying specially designed inland hulls to nearly every hireboat outlet on the Broads over the 1970s and 1980s.
As that business began to decline, Aquafibre sold to the big charter fleets, with many hulls going to Ireland for Emerald Star and France for Crown Blue Line.
Thinking of buying an ex hire boat like this one. Call me for a chat or mail me at steventruss1@aol.com 

Tuesday 5 May 2015

Colvic Northerner 26

I had the day at Morston Quay on the North Norfolk Coast carrying out a number of insurance surveys. This Colvic Northener 26 has a round bilge full displacement hull with long keel line and is complemented by a high foredeck with a dropping sheer on the deck line. These mouldings were often home fitted and the style and quality of build varies enormously.








Morston Quay
Colvic s directors Colin and Vic ,hence the name were based in Witham Essex and were prolific GRP moulders producing many different designs from the classic displacement round bilge boats to fast offshore cruisers. The majority of moulds were supplied to DIY fit out customers although some companies such as Northern Marine fitted out Colvic Northerner 27s to some success. The company, i think started in the late 60,s and finally finished in early 2000,s.

Surveyors comments: The Colvic name was synonymous with quality, strength and excellent sea-keeping. The hulls were built very strong compared with today's standards. 

Monday 4 May 2015

Surveying Classic Broads Cruisers

I have been Surveying quite a few Wooden Broads Cruisers again recently. They are very appealing to newbies to boating because for one reason they look like a real boat should, and also because of all the room that's available.The biggest reason buyers like them is the cost. You can quite easily find a six berth, 35 ft Broads Cruiser for under 10K. In fibreglass you would be lucky to get a diesel engine thrown in for that price! 

Lets start with the point that there are many Surveyors who are no longer in the business after performing pre purchase surveys on wooden boats. I almost gave them up myself years ago because surveying wood boats is fraught with risks. I've only ever owned wooden boats and at the ripe old age of 52 i now actually live on one myself. Saying that, mine is not a Broads Boat. Most Broads Cruisers were built just to hire, they were never meant to last for years and years and generally the majority of them were not particularly expensively built in the first place. Saying this many have been proven to be persistently durable, and are intact and with no indications of serious distress. Remember they are only being used on inland waters, they are not expected to cruise across the channel! 

Lets begin: Concealed areas within a hull are always a problem but, most Broads Cruisers are constructed in such a way that enough access is available to make a fair assessment. I always pull up all the floors and remove enough paneling that I can get a fairly good glimpse of the bottom and the lower sides. Carrying an electric screw gun is a must in order to do this quickly and effectively. 

My biggest job is removing all the internal fittings. That means I have to move a lot of mattresses, bedding, carpets and empty out lockers, etc. Once the interior is opened up as best possible, Im ready to begin. 


Three important tools are a slim light crow bar, the sort used for pulling nails. A light hammer and a standard blade screwdriver. I check the joints between planks and frames visually, looking for gaps or any sign that the plank is not tight against the frame. I then use the screw driver to test the wood for softness on both plank and frame near the mating surface. You should be very careful with your screwdriver or spike as they can be destructive! Many a Surveyor has got into serious trouble after the boat owner found thousands of spike holes in the bottom of his boat!  

I occasionally try to slip the crow bar under a frame and pry gently. If the frame moves, there is a fastener problem. I do this at every opportunity along the hog (internal keel) or chine area. Often the frame ends are split or soft, repairs are usually necessary.
Weepage is a process of very slow leakage, (this example was water coming in through the transom seam) very often involving the capillary effect in addition to just water pressure from outside the hull. Weepage is not referred to as leakage because the rate is so slow that the water evaporates nearly as fast as it enters the interior. It can occur with no sign of wetness, but inevitably leaves some trace of its existence such as stains.

Certainly its not feasible to go through the entire hull testing all frames and planks in this manner, and fortunately it is not necessary except for the keel area where this needs to be done wherever possible. Further up from the keel, I can limit the physical testing by looking for signs of weepage. Anytime there is evidence of water migrating through seams, corrosion of fasteners has to be suspected. Weepage shows up in various ways, often depending on whether the wood is painted or bare, its age and so on. 

Use the screwdriver for testing the hardness of the inner planking, particularly in the deep bilge or any place that is wet or looks suspect. The screwdriver blade is just the right tool, and if it goes into the wood, you know for sure that its deteriorated. Poking around like this is quick and easy so that most vulnerable areas can be quickly covered.

The chines are an area not only of high stress, but an area that is also prone to leakage and rot, and most Broads Boats rely on the chine for most of the hulls strength. The surveyor should take every opportunity to inspect the chine areas and when evidence of weepage is found, the area should be targeted for special attention to rot. I often find large areas of rot on the chine stringer as water leaks in through the deck joint or deck fittings and it accumulates on the top of the chine and can cause major defects over time. (see lower picture). 



Bottom Frames are often joined to side frames with very little on Broads Boats and the chine takes the brunt as no knees are fitted. Looseness, rot or corrosion on these chine fastenings is a warning sign that all is not well.

A steel strap helps support the chine timber here, but this is unusual and most broads boats reply purely on the plank fastenings to support this area.  
The two most common areas for sprung planks to occur is the garboard and the forefoot area. The forefoot planking is difficult to check because this is the point where the planks narrow into the stem. But, again, signs of weepage or leaking is usually present when fasteners are wasted and planks are loose. Use the screwdriver and insert the blade into the intersect of plank and stem and push hard. This should be done on both sides in every area that can be reached. Again, this does not take long if the area is accessible and will readily show up rot and looseness. Get inside the chain locker if possible or strip out the forward berth. I always want to get a good look at the inner stem and hog and where they are scarffed together. If the stem or hogs rotten then the front of the boat may have to be opened up! (major job!). 

The intersect of bottom and side planking to the transom is yet another area where leakage and deterioration are prevalent. This area is also often difficult or impossible to reach, being obscured by fuel tanks and exhaust pipes and whatnot. On larger cruisers you can strip the aft berth out and get in, but on Broads Yachts you may only be able to see the inner corners by using a mirror or camera, unless your very small and you can climb in through the transom hatch and around the rudder tube. If reachable, probe the wishbone transom frame from both above and below. Broom Cruiser, Navigators, Captains and even the Admirals suffer in this area. (ventilation problems). Probe from the intersect of bottom planks and frames, and transom plank and frame. If the wood is at all soft, the problem is serious and needs further opening up and investigation. Examine the intersect all the way up to deck level. Is there water leaking in from above? If so, what is it doing to the wood and fasteners? Check from the exterior: are there open seams and signs of rot on the corners? If you see it above the waterline, what's going on below? Remember that open seams are allowing rain water in, and fresh water can be disastrous.

Keel bolts are always difficult to inspect or comment on. Check these major structural members for signs of working. Look for unevenness of scarf joints or any other signs of movement or working. Probe the keelson with the screwdriver for evidence of softness. Check the intersects of transverse frames for signs of rubbing or chaffing that indicates movement. Check visible bolts and bolt heads for corrosion. Also check for discoloration around the bolt heads. If the wood appears white and soft, this is an indication of weepage. Be careful about diagnosing this as "electrolysis." Its probably not. I always suggest the removal of at least two sample structural keel bolts for examination of the fastenings and adjacent timber material. This task is obviously difficult and sometimes impracticable and should be approached when convenient, especially when there was no evidence of deterioration of the structural keel bolts or surrounding timber.
Black Bess (Ernest Woods Halfdecker) which i have a half share in has just had her keel removed after the keel was found to be moving- the keelbolts were completely corroded away. 
Example image
 If there is water getting at the bolts, serious corrosion must be suspected. The only conclusion is to draw the bolts and inspect them. Don't rely on just tapping these bolts to see if they're loose. They may be tight now, but may go loose when the hull is working. Bear in mind the forces that operate on a hull while underway. Be wary of oily bilges and wood that can obscure this evidence. Poke around in the wood surrounding the bolt head. If its soft, you can be sure that there is weepage and the bolt is subject to corrosion. 

Inaccessible Areas: These are the areas that almost invariably cause the surveyor his greatest problems for he can't get at them to check. Frequently, these are the areas where structural deterioration takes place because neither interior inspection or maintenance is possible.
·        Outboard and under fuel tanks
·        Behind large exhaust pipes and mufflers
·        Under refrigeration and freezers
·        Under shower pans
·        Under lined lockers
·        Behind hulls that have full hull side ceilings

There's one thing you'll notice about most of the above listed areas and that is the potential for condensation and lack of air flow in these obscured areas which is highly conducive to causing deterioration of wood and metals. These obscured areas should be viewed with extreme caution. The only acceptable conclusion is guilty until proven innocent. To prove soundness, fasteners or planks must be pulled.
A good example of this was when I was restoring my Grand Banks 42, when i stripped out the aft cabin to fit a double berth the bulkheads below the water tanks were like 'cheese'. It was all to do with the ventilation around the water tanks / trapped dead air! 
Ventilation has a two-fold importance in wooden boats: removal of air saturated with moisture vapour, and introduction of unsaturated (dry) air to permit drying of moist woodwork. It is not easy to ensure that dry air circulates over all the woodwork in a boat. Whilst air may be circulated into a particular compartment it may not circulate through out the whole area unless points of entry and departure are correctly sited. Small areas are often partially or completely enclosed so that air circulation is impeded. These are the so called “dead-air” spaces in which pockets of stagnant moist air are trapped. Often by drilling a few well sited auger holes sufficient ventilation can be provided in what might otherwise be a small dead -air space.
Failed or improperly designed fuel and water tank foundations are a common cause of catastrophic hull failure. Because of the extreme weight of tanks, if supports fail, or were never properly designed in the first place, the planking or individual frames could end bearing a major part of the tank load. When this happens, hull failure usually results. 

Again, when i brought back my Grand Banks 42 from Scotland, on the journey home i remember constantly checking the fuel tanks. 4 x 300 gallon tanks full with fuel sitting on wooden stringers, now that's some weight. Be they cylindrical or square, tanks on saddles or on decks not fully supported by hull girders must be checked and the entire load bearing structure examined and evaluated. This is usually not as difficult as it might sound, for anyone with a good knowledge of proper construction can quickly size it up if the structure is accessible. If there is any doubt at all, particularly on aging structures, then other means of evaluation must be found. One of my fuel tanks is leaking slightly from underneath, the only answer is one day i will have to replace it! (major job). It will be interesting to see the hull condition once it has been removed. 

Check out the following u tube clip! Not the way i will be doing it! 


If the surveyor has done a good job with the interior, then his work on the bottom is going to be the easiest part of the job. By this time, he already knows if there are loose planks, bad frames, deterioration, weepage or leakage and where all these things are located. Long before it comes out of the water, he has a pretty good idea of whether this is a sound hull, and in many cases he'll already know that it isn't, so there's no point in hauling.

Nailing hulls is the common method here on the Broads. Nails cannot be pulled without causing much damage to the plank, if they can be gotten out at all. Inspecting the heads only tells one the condition of the head, not the rest of the nail. And tearing planks off means that they have to be renewed and the cost far too high. Nondestructive methods such as X-ray are both costly, difficult and not necessarily reliable.

Screw Fastened Vessels: Utilizing all the techniques outlined above, along with removal and inspection of fasteners, can provide a reasonable degree of certainty as to a hull's soundness. Moreover, screw fasteners can be replaced if they have good holding ground, meaning that planks and frames are not split or deteriorated.

To evaluate a screw-fastened bottom, first isolate the likely problem areas, including all of the garboards, under fuel tanks, and so on. One should not resort to the practice of laying out a pattern of evenly spaced points and pulling fasteners in this method as it is strictly hit or miss. 


First examine for:
·        Cupped or warped planks
·        Open seams and weepage from interior after bottom is dry
·        Planks with split ends or splits anywhere
·        Loose seams
·        Sound planks with heavy hammer for sound of looseness.
·        Discoloration around screw heads
·        Special attention to butt ends
·        Under tanks and engines - stress from heavy loads
·        Damp environments like under water tanks,etc.

All of the above areas should be marked and targeted first, for it is here where the problems are likely to be. Then, if all these suspect areas prove out okay, you may not even need to pull fasteners in the non-suspect areas and this will reduce the work load greatly. The objective here is to determine whether the hull has a general condition of wasted fasteners or whether it is isolated due to the initiating factors discussed above.

Remember you need permission from the owner to pull 
fastenings. Tight fasteners should be hard or impossible to move. If it won't turn, don't bother trying to force it because its okay. Fasteners that just spin without backing out are bad and one needn't waste his time trying to get them out.

I will get back onto this subject of surveying wooden boats in the future, there are so many more areas left to discuss. Decks being one of them. Ive been chasing a leak on the decks on my boat for about 6 months and im still yet to find it! But hey, that's another story.

Stripping out the aft cabin on my boat- this is where you find out if you missed something! 
My services: For a wooden boat survey, the vessel should be blocked off ashore as it is not possible to carry out a useful assessment of the underwater hull during a one hour lift and hold in a travel hoist. It is possible to inspect a hull between tides provided the ground is firm. The survey will often require some dismantling in order to access hidden areas. Here, the focus is on any decay or deterioration from rot, marine borers or electrolytic action, and on the condition of the fastenings. It is important that I carry out as thorough an examination as possible by getting good access to the hull and frames. The costs of repairs can easily be beyond the market value of the boat so it is vital for you to get the best possible idea of what you are buying from the outset.

Lifting 'Destiny' out for the first time in Norfolk 2014. 
2015 - and finished - for now....
For older wooden boats I can carry out a one hour preliminary inspection to assess if the boat is worth lifting out for survey and what dismantling needs to be done. I have surveyed many classic cruising yachts and power boats, both plank on frame and modern epoxy-wood construction, as well as traditional Broads Cruisers, from Brooms to Windboats. I've even got the experience from repairing a few of my own over the years so if you have a project in mind, call or e mail and we can go through the options. steventruss1@aol.com